楼主: bobbi

【颁奖啦!】AS3992知多少?参与答题赢大礼(第二期)

  [复制链接]

该用户从未签到

发表于 2015-12-1 11:49:18 | 显示全部楼层
分享到:
此帖仅作者可见

使用道具 举报

  • TA的每日心情
    奋斗
    2018-9-26 13:39
  • 签到天数: 145 天

    连续签到: 1 天

    [LV.7]常住居民III

    发表于 2015-12-1 17:15:49 | 显示全部楼层
    此帖仅作者可见

    使用道具 举报

  • TA的每日心情
    奋斗
    2018-9-26 13:39
  • 签到天数: 145 天

    连续签到: 1 天

    [LV.7]常住居民III

    发表于 2015-12-1 17:16:23 | 显示全部楼层
    此帖仅作者可见

    使用道具 举报

  • TA的每日心情
    开心
    2013-12-14 15:53
  • 签到天数: 2 天

    连续签到: 1 天

    [LV.1]初来乍到

    发表于 2015-12-1 23:20:55 | 显示全部楼层
    此帖仅作者可见

    使用道具 举报

    匿名  发表于 2015-12-1 23:27:43
    1) AS3992芯片标准工作频率,支持何种协议?
    RFID frequency range 840MHz to 960MHz,ISO18000-6C (EPC Gen2) full protocol support,ISO18000-6A,B compatibility in direct mode
    2)AS3992 的FIFO register有多大?
    24 byte
    3)AS3992 的PLL由哪些部分由组成?
    PLL section with integrated VCO, supply section, DAC and ADC section, and host interface section.
    4)AS3992 收送数据时,可选的Normal模式和Direct模式有何区别?
    1. Normal Data Mode: In this mode, the TX and RX data is transferred through the FIFO register and all protocol data processing is done internally.2. Direct Data Mode: In this mode, the data processing is done by the host system,ISO18000-6A,B compatibility in direct mode
    5)AS3992芯片的发射天线阻抗要设计成多大合适?
    AS3992芯片的发射天线阻抗要设计成50Ω
    回复

    使用道具

  • TA的每日心情
    慵懒
    2015-10-29 15:32
  • 签到天数: 34 天

    连续签到: 1 天

    [LV.5]常住居民I

    发表于 2015-12-1 23:29:20 | 显示全部楼层
    此帖仅作者可见

    使用道具 举报

  • TA的每日心情
    慵懒
    2015-10-29 15:32
  • 签到天数: 34 天

    连续签到: 1 天

    [LV.5]常住居民I

    发表于 2015-12-1 23:31:20 | 显示全部楼层
    此帖仅作者可见

    使用道具 举报

    该用户从未签到

    发表于 2015-12-1 23:32:18 | 显示全部楼层
    此帖仅作者可见

    使用道具 举报

    匿名  发表于 2015-12-1 23:39:41
    答案一:协议: ISO180006c/b 工作频率:900MHz
    答案二:24 bytes
    答案三:a voltage control oscillator (VCO), prescaler, main and reference divider, phase-frequency detector, charge
    pump, and loop filter

    答案四:
    TX:
    In normal mode, all signal processing protocol coding, adding preamble or frame-sync and CRC, signal shaping, and modulation) is done
    internally.
    Direct mode is applied if the user wants to use analog functions only and bypass the protocol handling supported in the reader IC.Direct Mode Using Serial Interface (SPI).
    RX:
    In the normal mode, the digitized output after decision circuit is connected to the input of the digital portion of the receiver. This input signal is the
    sub-carrier coded signal, which is a digital representation of modulation signal on the RF carrier.

    The direct mode is applied in case the user wants to use analog functions only and bypass the protocol handling supported in the reader IC.  “ Normal模式支持ISO/IEC18000-6C,Direct模式可兼容IS018000-6A/B”


    答案五:50Ω
    回复

    使用道具

    您需要登录后才可以回帖 注册/登录

    本版积分规则

    关闭

    站长推荐上一条 /2 下一条



    手机版|小黑屋|与非网

    GMT+8, 2024-3-29 14:27 , Processed in 0.191940 second(s), 30 queries , MemCache On.

    ICP经营许可证 苏B2-20140176  苏ICP备14012660号-2   苏州灵动帧格网络科技有限公司 版权所有.

    苏公网安备 32059002001037号

    Powered by Discuz! X3.4

    Copyright © 2001-2020, Tencent Cloud.